Clean Storm Pump Pressure Feed Conversion Kit (self install) can be used on all makes and models or carpet cleaning machines.

Brass Ferrule .821 inches X 1 inches Long X .025 Gauge Common for 1/2in ID Hose 32577 Four units dealer installed

Air and Water Hose HBD Thermoid Inc ValuFlex (ValueFlex) 3/8" ID Per Foot 200psi Black GS GP  10 ft of 3/8" ID 800 psi burst, 200 degree hot water hose. Cut in half to two 5 ft sections. We will assemble this for you with crimped ends These hoses are used to make the in and out hose connections from the sink to the fresh tank and back.

Air and Water Hose HBD Thermoid Inc ValuFlex (ValueFlex) 1/2" ID Per Foot 200psi Black GS GP (or similar) 5 ft of 1/2" ID 800 psi burst, 200 degree hot water hose. Used to replace the clear spiral wire reinforced hose currently installed under the hood of your machine. Usually you might have to shorten and cut in half to allow for the Y filter installation.

Includes 1  Thermal Relief Valve 145 Degrees F 3/8" Mip X 1/4" Plastic Barb Control Devices Inc (or similar) 145 safety water temp sensor with 3/8" Mip X 1/4" barbed connector Will protect your water pump from water hotter than 145 degree by discharging water that is too hot back into the sink or shower.

Includes one 3/8in Mpt X Female Garden hose Swivel Fitting Brass with gasket - 8.901-292.0 - 30048

Kit includes 2 units Brass Street Elbow 90 Degree 3/8" Mip X 3/8" Fip Used with JE Adams booms Item #6050 and Item #6083 BR284 B186

Kit includes 1 unit  Four Way Brass Cross 3/8" Fip X 3/8" Fip X 3/8" Fip X 3/8" Fip 6FP-BCross 8.705-197.0 - 28042

Kit includes 2 units  3/8" Mip X 3/8" Barbed Brass Fitting 32-013 Straight

Kit includes 2 units Pressure Washer QD Female Coupler X 1/4 in Mip Stainless Steel 8.707-110.0 - Legacy Shark 2-2001SS or similar

Kit Includes 1 unit  Karcher 8.707-103.0 - Pressure Washer QD 1/4in Fip X 1/4in Female Socket Coupler Stainless Steel - 87071030 - 2-2000SS or similar

Kit Includes 2 units 1/4" Mip X 3/8 in Hose Barb Brass - 8.705-104.0 - 87051040 32-012 32012 BR020

Kit Includes 2 units  Pressure Washer QD 1/4" Fip X 1/4" Male Nipple Plug Stainless Steel Coupler

Kit Includes 1 unit  1/4" Mip X 1/4" Fip Street 90 Brass Elbow BR282

Kit Includes 1 unit 1/4" Mip X 1/4" Fip Brass Extender 28192

New upgrade Kit Includes 1 Brass "Y" Filter 1/2" Fip Strainer 342007 - BY5050 87070640 E132 8.709-958.0  Replaces the plastic strainer that is currently installed between fresh tank and water pump.  Can handle more hot water and pressure than the plastic does.

New upgrade Kit Includes (2)  1/2" Mip X 1/2" Barbed Brass Fitting 32-017 Straight  Two included, one for each side of the above Y filter to assist in replacing plastic filter. Re-use original hose clamps that are currently holding plastic filter to secure this assembly

 



 

All the clear wire reinforced 1/2" suction hoses in the motor box will have to be changed out to the hot water rated pressure hoses.
Most of the assembly work will be done by use before the parts ship.  You will just add the parts to the bottom of the fresh water tank and change out the motor box hose and filter with this hot water rated hose and filter. 
Remove 1/4" Acorn Strainer from bottom of fresh water tank and install on 1/4" Mip X 1/4" Fip Socket Flow through QD
Install 1/4" Male Socket QD / 90 /extender to the location that the acorn strainer once sat.
Install 1/4" Mip X 1/4" Female Flow Through QD on return hole from pump bypass in bottom of fresh water tank. 

You are all set!  If you you want to suction feed and use the fresh water tank, you just remove the direct connect hoses and snap in the acorn strainer on the QD.
If you want to pressure feed your pump, just remove the acorn strainer and install you twin 5 ft hoses up to the faucet adaptor.
Easily toggle back and forth between pressure feeding and suction feeding your pump. 
Easily toggle back and forth between using the fresh tank or direct connect. 
Conversion can be done on all makes and models of portable carpet cleaning machines. 
145 water sensor monitors your incoming and circulating water temperature to make sure that you stay under the 145 degree mark that is safe for pump head seals.   You can optionally add 1/4" Id hose to the sensor barbed connectors but as of right now just point the outbound barbed fitting into the sink. 

Please note the above kit is for machines that have 1/4" pipe connection in the bottom of the fresh water tank.  
If you have a Nautilus extractor you will need to purchase two more brass parts.  1/4" Mip X 3/8" Mip hex nipple (part BR132) to convert the pump bypass return to 1/4" mip after you remove the elbow, and a 1/4" Fip x 3/8" Mip brass bushing to convert the hole under the acorn strainer from a 3/8" Fip to a 1/4" Fip (part A00168).

Optional:
Labor charge for use to install this kit for you in your machine if located at our location in San Antonio TX $150.00

Clean Storm

AutoFillKit

Clean Storm Automatic Fill Kit for Carpet and Tile Cleaning Machines

What are some the best features to look for in an electric flood extraction / vacuum

Narrow down my portable extractor search!